Model NO.: YMXG-20
Color: Customized
Trademark: yimei
Transport Package: Container Package
Specification: 8*2.25*2.25m
Origin: Qingdao, Shandong
HS Code: 8421219990
Model NO.: YMXG-20
Color: Customized
Trademark: yimei
Transport Package: Container Package
Specification: 8*2.25*2.25m
Origin: Qingdao, Shandong
HS Code: 8421219990
Sludge sedimentation tank --lamella clarifier
Introduction
The lamella clarifier is also known as an inclined plate sediment tank. It is a high-efficiency combined settling tank that uses many densely packed inclined tubes in the sedimentation area to allow suspended impurities in water to settle. As the water rises along the inclined tubes, the separated sludge descends along the tubes due to gravity and is discharged in concentration. This type of tank can improve sedimentation efficiency by 50~60%, and it can increase treatment capacity by 3~5 times within the same area. It can be designed with different flow rates of inclined plate sediment devices according to the raw wastewater test report, and usually requires flocculant addition.
The inclined plate sediment tank has a 60° dip angle to the ground. When water flows up along the inclined tube, the sludge and suspended solids can settle onto the inclined tube, then slide back to the sludge layer relying on gravity, settle into the sludge collecting hopper, and flow into the sludge tank via a sludge pipe for separate treatment or comprehensive utilization. The supernatant fluid gradually rises to the top.
Feature
1), Simple structure, no wearing parts, wear well, reduce maintenance
2), High-efficiency treatment of wastewater with high solid content (grit, clay, lime, metal particles)
3), Installed indoors and outdoors (but ambient temperature needs to be greater than 0°C)
4), The inclined plate sedimentation tank can create a good laminar flow environment for better sedimentation.
5), Intensive design minimizes hydraulic disturbances caused by wind or temperature changes.
6), Suitable for on-site unattended automatic continuous operation
7), Small occupy area, low investment, high efficient. Small power, save energy.
8), Short retention time, high sediment efficiency, no sludge back flow.
 Application scope
1), Electroplate effluent contain many kinds of metal ions, Cr, Cu, Fe, Zn, Ni etc remove rate all above 90%, after treatment, all can reach discharge standard.
2), Coal mine, mineral processing waste water all can make the turbidity from 500-1500 mg/L reduce to 5 mg/L.
3), Printing and dyeing, bleach and dye etc effluent chroma removing rate reach 70~90%, COD remove rate 50-70%.
4), Tannery, food etc industrial sewage COD remove rate 50~80%, impurity solids remove rate above 90%.
5), Chemical waste water COD remove rate 60~70%, chroma removal rate 60~90%, suspended solids reach discharge standard.
6), Industrial production waste water; Filtration pre treatment; Filtration of effluent and backwash water; River water purification sludge concentration.
4. Structure introduction
1), Inclined tube material : PVC, PE, PP ,inclined plate: carbon steel lining
2), Inclined tube cross section is regular hexagon, inclined plate cross section can be parallel-plate.
3), The cleaning water area height is 1.0-1.5m above the inclined pipe top, the water distribution zone below the bottom no less than 1.0-1.5m, mechanical discharge sludge, the water distribution zone height should more than 1.6m, convenient install and maintenance.
4), The Re number in water flow less than 500, Fr number is 10-3-10-5 in inclined pipe.
5), Inclined tube design flow rate is 1.0-4.0mm/s, inclined plate 10-20mm/s.
 Technical data
| Specification model | YMXG-5 | YMXG-10 | YMXG-15 | YMXG-20 | YMXG-25 | YMXG-30 | YMXG-40 | YMXG-50 |
| treatment capacity(m3/h) | 5 | 10 | 15 | 20 | 25 | 30 | 40 | 60 |
| equipment size (m) | 2.2*2*3.5 | 2.25*2.25*5 | 2*2.5*6 | 8*2.25*2.25 | 8*3*4.5 | 8*3.5*4.5 | 10*2.0*2.3 | 11.7*2.2*2.5 |
Â
Sludge sedimentation tank --lamella clarifier
Introduction
The lamella clarifier is also known as an inclined plate sediment tank. It is a high-efficiency combined settling tank that uses many densely packed inclined tubes in the sedimentation area to allow suspended impurities in water to settle. As the water rises along the inclined tubes, the separated sludge descends along the tubes due to gravity and is discharged in concentration. This type of tank can improve sedimentation efficiency by 50~60%, and it can increase treatment capacity by 3~5 times within the same area. It can be designed with different flow rates of inclined plate sediment devices according to the raw wastewater test report, and usually requires flocculant addition.
The inclined plate sediment tank has a 60° dip angle to the ground. When water flows up along the inclined tube, the sludge and suspended solids can settle onto the inclined tube, then slide back to the sludge layer relying on gravity, settle into the sludge collecting hopper, and flow into the sludge tank via a sludge pipe for separate treatment or comprehensive utilization. The supernatant fluid gradually rises to the top.
Feature
1), Simple structure, no wearing parts, wear well, reduce maintenance
2), High-efficiency treatment of wastewater with high solid content (grit, clay, lime, metal particles)
3), Installed indoors and outdoors (but ambient temperature needs to be greater than 0°C)
4), The inclined plate sedimentation tank can create a good laminar flow environment for better sedimentation.
5), Intensive design minimizes hydraulic disturbances caused by wind or temperature changes.
6), Suitable for on-site unattended automatic continuous operation
7), Small occupy area, low investment, high efficient. Small power, save energy.
8), Short retention time, high sediment efficiency, no sludge back flow.
 Application scope
1), Electroplate effluent contain many kinds of metal ions, Cr, Cu, Fe, Zn, Ni etc remove rate all above 90%, after treatment, all can reach discharge standard.
2), Coal mine, mineral processing waste water all can make the turbidity from 500-1500 mg/L reduce to 5 mg/L.
3), Printing and dyeing, bleach and dye etc effluent chroma removing rate reach 70~90%, COD remove rate 50-70%.
4), Tannery, food etc industrial sewage COD remove rate 50~80%, impurity solids remove rate above 90%.
5), Chemical waste water
High-purity titanium sputtering targets for integrated circuits, flat plate targets for the LCD display industry, sputtering targets for semiconductor components, and targets for the solar industry. High purity titanium evaporative material is widely used in vacuum coating..High purity titanium wire can be used as bonding material for human implant devices; In biology, medicine and other fields, has a large number of applications such as Large-scale integrated circuit manufacturing, LCD targets, decorative coatings.
Stainless Steel Belt,Thin Titanium Foil Belt,S316 Foil Stainless,Chrome Nickel Base Alloy
Ningbo Boss Metal Material Co., Ltd. , https://www.boss-metal.com