S SH Horizontal Sea Water Pump

Products Name: BB1 Double Suction Pump,Centrifugal Pump

Performance range:
Flow: Q=144-12500m³/h
Head: H=9-140m

Structure:
SH pump using the level of open, with a double suction impeller. suction pipe , discharge pipe and the lower part of the pump body casting together, do not need to remove the pipeline and the motor will be able to easily check the pump rotor parts.

Model specification:
10 SH ---13 A
10:Suction diameter(inch)
SH:Single stage double suction level of open
13:The number is integer divisible by 10
A:Impeller's cutting time. The order is A B ...

Shaft Sealing:
The pump adopts soft packing, the sleeve can be replaced with the shaft seal part, can also according to user's requirements with mechanical seal.

Transmission:
Pump is driving through the flexible coupling by the motor , from the drive end, the pump is counter clockwise rotation (according to the special order supply clockwise rotation of the pump).

Bearing and balance device:
Bearing body (rolling bearing or sliding bearing) installed at both ends of the pump shaft, the axial force balance by the double suction impeller , the residual axial force balance by the rolling bearing . Rolling bearings with grease lubrication, sliding bearing with thin oil lubrication.

Materials:
Casing: cast iron ; Shaft sleeve: cast iron  ;  Sealing Ring: cast iron  ; Shaft: high quality carbon steel;Impeller: Cast iron, cast steel;
According to the transmission medium is different, the pump materials and models are also different. 
1. Clean liquid without solid particles, SH Type pump all material is cast iron, SHG type pump body is cast steel , carbon steel and stainless steel. Rotor parts is carbon steel or stainless steel.
2.Sea water and other corrosive media, SHN type of pump body material is nickel cast iron, SHF type pump body material is stainless steel.
This type of pump when the matching motor power in the following 110KW with a common base. If the Common base is greater than 100KW, the order must be explained. if users have special requirements for motor pump , please state in the order. 
Using rolling bearing:


Using sliding bearing:

A Solenoid Valve is an electromechanically operated valve. The valve is controlled by an electric current through a solenoid: in the case of a two-port valve the flow is switched on or off; in the case of a three-port valve, the outflow is switched between the two outlet ports. Multiple solenoid valves can be placed together on a manifold.

Solenoid valves are the most frequently used control elements in fluidics. Their tasks are to shut off, release, dose, distribute or mix fluids. They are found in many application areas. Solenoids offer fast and safe switching, high reliability, long service life, good medium compatibility of the materials used, low control power and compact design.

Besides the plunger-type actuator which is used most frequently, pivoted-armature actuators and rocker actuators are also used.

Solenoid valve designs have many variations and challenges.

Common components of a solenoid valve:

• Solenoid subassembly
  • Retaining clip (a.k.a. coil clip)
  • Solenoid Valve Timer
    
  • Solenoid Coil (with magnetic return path)
  • Core tube (a.k.a. armature tube, plunger tube, solenoid valve tube, sleeve, guide assembly)
  • Plugnut (a.k.a. fixed core)
  • Shading coil (a.k.a. shading ring)
  • Core spring (a.k.a. counter spring)
  • Core (a.k.a. plunger, armature)
• Core tube–bonnet seal
• Bonnet (a.k.a. cover)
• Bonnet–diaphram–body seal
• Hanger spring
• Backup washer
• Diaphram
  • Bleed hole
• Disk
• Valve body
  • Seat
  • air valve
  • water inlet valve
  • control valve
    

The core or plunger is the magnetic component that moves when the solenoid is energized. The core is coaxial with the solenoid. The core's movement will make or break the seals that control the movement of the fluid. When the coil is not energized, springs will hold the core in its normal position.

The plugnut is also coaxial.

The core tube contains and guides the core. It also retains the plugnut and may seal the fluid. To optimize the movement of the core, the core tube needs to be nonmagnetic. If the core tube were magnetic, then it would offer a shunt path for the field lines. In some designs, the core tube is an enclosed metal shell produced by deep drawing. Such a design simplifies the sealing problems because the fluid cannot escape from the enclosure, but the design also increases the magnetic path resistance because the magnetic path must traverse the thickness of the core tube twice: once near the plugnut and once near the core. In some other designs, the core tube is not closed but rather an open tube that slips over one end of the plugnut. To retain the plugnut, the tube might be crimped to the plugnut. An O-ring seal between the tube and the plugnut will prevent the fluid from escaping.

The solenoid coil consists of many turns of copper wire that surround the core tube and induce the movement of the core. The coil is often encapsulated in epoxy. The coil also has an iron frame that provides a low magnetic path resistance.

Solenoid Valve

Electromagnetic Valve, Pneumatic Component, Pneumatic Solenoid Valve, Air Compressor Valve,Solenoid Valve Timer

NINGBO BRANDO HARDWARE CO.,LTD , http://www.brandopneumatic.com