Cable Tester / Cable Tester Model:HAD-SML-8828
Product introduction: on-line function, crosstalk test, hunt function, open circuit
1. Use MS and MR to test open, short circuit and jumper of 5E/6E network cable, telephone line, BNC cable and USB signal cable.
Reverse connection, crossover, pairing and other connection conditions, and intuitively displayed on the LCD.
2. Perform cross-talk test on the network cable to solve the potential trouble of slow network speed.
3. It can identify and find the line to be searched at the remote end through the prompt of the volume in many network cables, telephone lines and other various metal lines.
Hunting line length of up to 3000 meters with anti-jamming and high sensitivity, the volume adjustment knob on the receiver can adjust the sensitivity size.
4. Judging the open point, can accurately determine the open circuit of the cable head at an end point (left, right or middle)
5. Automatic delay shutdown.
6. Low voltage display when voltage is too low.
7. Self-test and automatic adjustment of various test conditions, automatic supplement to battery capacity and ambient temperature changes.
Test cable types: 8P8C:UTP twisted-pair network cable; E6P6C telephone line; USB signal line; F(S)TP BNC coaxial cable.
LCD display features: dot matrix 128x64 size: 48x32mm
Units: METER, FEET, YARDS
Maximum length of test cable: 1200m
Accuracy: 2% (±0.5m or ±1.5ft)
Power specification: DC 9V battery power consumption: operating current ≤15mA
Volume: 149×66×23mm Net weight: 200g
Packing: Blister + color box Weight: 650g/pc
Operating temperature/humidity: 0°C-50°C/20%-70%
8368 series digital liquid crystal display network cable tester is the company's product after many years of research and development and testing, has independent intellectual property rights, a number of patents. Product performance Ling first international level of similar products, with low power consumption, environmental protection, high efficiency and so on. Adopt ordinary AAA battery, insert cable automatic test, support stand-alone test, dual-machine synchronous display test, improve efficiency. Stylish, smart, sturdy design.
First, stand-alone test: Turn on the power switch, and insert the two ends of the twisted pair into the M and L sockets of the unit respectively. The tester LCD screen displays TEST(ING) and the test is performed automatically.
When the LCD screen number does not jump, the displayed result is the cable connection.
Second, the use of dual-use methods: Use two identical machines, press the "MODE" button for more than 2 seconds, set one of the "S (LSVE)", the other for "M (ASTER)" can be tested . Plug both ends of the cable into the port labeled "M" on the machine (this method is suitable for remote testing). After the machine automatically tests and locates, the test results will be displayed on the respective LCD screens. The definition of each screen is as follows: The previous line number is the end of M itself, and the lower line number is the other end of S.
Third, the LCD screen status explanation:
1.MISWIRE: Wrong wiring; wrong cable connection, all displayed when open circuit is short-circuited.
2.OPEN: open circuit; open cable, and no display under the corresponding cable number.
3. SHORT: Short-circuit; there is a short-circuit of the cable, and the corresponding cable number jumps, no display below.
4.RESEVED: cross-pair, with cable 1 & 2, 3 & 6, 4 & 5, 7 & 8 any one of the counter-time display.
5.UTP: Unshielded cable, 0 no display.
6.FTP: There is a shielded cable and 0 is displayed.
Fourth, warning!
This tester is prohibited to test network cables and telephone lines with voltage, otherwise it will seriously burn out the machine.
This tester uses a AAA battery. If the LCD screen is dark, replace the battery.
RJ45 copper clips cannot be tested when not fully pressed. Otherwise it will permanently damage the port!
No RJ11 port is specified, and the test telephone connection (RJ11) is prohibited. Otherwise it will cause permanent damage to the machine!
This product has an LCD screen that cannot be thrown and thrown to avoid damage to the LCD screen.
This station is suitable for industrial, civil construction, roads, railways, bridges, electric power, water conservancy, port terminals, airports and other projects. It can be used as a mixing equipment for commercial concrete production, and combined various forms different specifications concrete mixing plant according to the needs of different users.
Automatic Batching Machines,Weigh Batching Machine,Material Batching Machine,Aggregate Concrete Batching Machine
Shandong Zeyu Heavy Industry Science and Technology Co.,Ltd. , https://www.sdmobileconcretebatchingplant.com